OVERTURE Matte PLA 3D Printer Filament 1.75mm, Matt Surface & Low Warping Filament 1kg Spool (2.2 lbs), Accuracy +/- 0.02 mm, Fit Most FDM Printers (Matte Light Brown)

Just WOW!. I'll update with photos of my prints later on. I've been searching for matte filaments and there seems to be limited options. Not only have i think i found it, i dear say i found my goldilocks filament. Ordering 3 more rolls next week as I've been printing 24hrs a day since i got it a few days ago. Excited to try other colors. Roll was nicely wound and print quality is astounding, printing is very easily and was dialed very quickly. and i have zero complaints so far. Layer lines are pretty much invisible even at .2 layer heights. .13 is jaw dropping. Been printing an order for a local hobby shop and they at first didn't believe it was 3d printed as it looked multitudes better than previous filament I've used on their order. I've been printing on my mostly stock ender 3 v2. Only modifications are z-brace rods, bltouch, dual z and printed z motor mounts. Printing here the update NY winter is usually challenging as where i print in my home can be as low as 10c ( will be finishing my enclosure soon). Saying that my only struggle has been minor corner warping and bed adhesion. but i doubt that would be an issue in warmer rooms. The issue has been resolved though as i really squish my first layer (leaves very fine elephant foot that cleans quite easily with a sharp hobby knife or 220grit sand paper) since i print 7-20 parts at a time. Can't afford failures. I am printing on the stock textured side of the ender 3 glass bed. For those with an ender 3 i do Hot end at 195-200c, 60c bed temp at 40mm sec (as i prefer quality over speed ) retract 6.5mm 50mmsec, default cura coasting settings and filament equalizer enabled. 75%-100% fan after initial 2 layers. I'd also like to add that my printed upgrades are done in hatchbox abs for strength and temperature resistance. But now any parts that aren't at risk of high temperature exposure I'm using this matte black pla because it looks that amazing and is suitably strong. If I run into any issues I'll update accordingly. Update 7 Days Later So i ordered this filament for an order for a hobby shop. Printing drag racing slot car stands. I printed 96 of these in 4 different filaments. After the first 28 this filament arrived and after the first test prints i was amazed and now only use this filament. I went through the whole 1kg roll in 6 days. Ordered another and already been printing into the 2nd roll. I've updated my nozzle temp to 210c and I'm using a .8 brass nozzle. A worth while mention is these stands i print they're only 3 bottom 2 top, 1 perimeter and 0% infill. And they're almost perfect, very light and just as strong as previous prints with .4 using 3b 4t and 2 perimeter. The watering can is from thingiverse and printed at 60mmsec, 3 bottom and in vase mode. Also worth noting i check filament diameter periodically as i go through the roll and so far it's been between 1.72-1.77mm. Overall still my new favorite go to pla. I definitely prefer a matte finish and this filament definitely delivers.

This filament prints beautifully and gives a smooth, matte surface that hides layer lines really well. It sticks nicely to the bed and has very little stringing once the settings are tuned. The color is rich and consistent throughout the spool. Great choice for aesthetic prints or display pieces — reliable and worth the price.

this filament is the best i've used, it prints very cleanly with minimal visible layer lines. my only complaint comes from the packing. i'm not sure if it was an issue with the factory or the packing warehouse but i know for sure that it wasn't a shipping issue because the other items it was packaged with were completely intact. the box and the filament spool itself were completely crushed. i was hoping that it was just the box that was destroyed so i didn't take a picture of it before i opened it, only after, so the box in the photo is slightly more bent into shape because i had trouble opening it. i find it hard to believe this was an issue with shipping because i've owned overture filament before and the vacuum sealed package is very heavy and tough. it would take a lot of force to destroy it in the condition i received it. i considered returning it but i didn't want to wait another few days/weeks to start on my project so i tried my best to flatten the edges of the spool. so far it hasn't had any issues on my printer despite that. i'm still giving it 5 stars considering this doesn't really effect the product itself and i've never had this issue with overture before, but this is something i wanted to share hoping overture or amazon become aware of this. if it was destroyed any further it would've been unusable.

Love the brand and the Matte Black color one of my favorite PLA filaments. Recently use it on this model as the black color. I was running short on it with a few hours remaining and was able to get another roll same day right in time as the previous roll ran out. The print speed is great ran standard speed on my Bambu H2S no clogs and no stringing made it very easy to use. The cardboard spools although not ideal fit perfectly into the AMS. As for functionality, it is perfect for any PLA prints in my opinion.

I needed a filament that best matched Haze Grey and that wasn't going to cost me a couple hundred dollars for a color calibrated filament. US Navy Ships are painted in 2 colors on the exterior, Haze Grey and Deck Grey. The grey color you see when you look a Carrier or a Destroyer is Haze Grey, Deck grey is a darker grey and is usually painted on the floor of traversed spaces aka where a sailor may step on. I needed something that was close after a lot of research I bought 3 grey PLA's and of the 3, this was the closet in color. The ship I printed was 1/700th scale using a .2mm Nozzle and a .08 nozzle layer height. I used an Ender 3 Pro and I printed on a piece of G10 heated up to 60 degrees. I had lot a bunch of trouble getting this to stick at first. I refuse to use glue sticks, hair sprays, etc to make them stick and I almost caved here. I think the problems with getting this to stick deal with the smaller surface area of a .2mm nozzle. I found if I used a brim of at least 8mm in diameter then I had a much better chance of getting it to stick. if you look at the one picture you can see my thumb, to get an idea of how small some of the parts were. I had some stringing on some of the smaller parts but because of how long these take to print and the fact I knew I was going to do some post processing I wasn't too worried. I also tried some larger prints using a .6mm nozzle and these had no issues at all. I printed some PCB din rail holders since I already had this filament queued up and the filament had no issues with sticking or stringing. The matte color does a really good job of hiding the layer lines you can still see them in the right light or up close. This is the first time I've ever tried this brand. I generally stick to the same 1-2 brands that I know and trust. I have mixed feeling amount wether I would buy more from this same company. on the one hand I had a lot of trouble when printing really small but on the other with larger nozzles I've had no problems. this is problem due to a lack of experience with printing really small, fine detail models.

This is one of my main go-to brands of filament. I have had zero issues with this brand and have purchased many colors. The price is always great and normally buy multiples. This filament is very sturdy and I have had zero breakage using it. It prints perfect every time, except that occasional user error that happens sometimes. I tend to stick with brands I know that work well for the money and this is one of those brands.

This overture matte Pla is my true favorite of all PLAs. Not sensitive to moisture, very nice variety of colours, hide the layers, prints east and fast (have used them at 300mms without an issue), zero clogging problem. Overall, my favorite if all. Specially this colour wood, is fantastic for home decor. I printed this Montessori block toy for my baby girl and looks great with some fuzzy skin, people really think is wood.

So far the color is fine and true to the photo in Amazon . I usually love Overture filaments but this rating is for the reel. The reel it came on this time is fighting with my Anycubic Ace Pro. I have to constantly watch it because it is not smooth on the outside so hangs up. This is the first reel I have had these issues with. So far only an hour in and I have to constantly monitor it. I have used their other colors and they worked flawlessly, but I think this reel is defective. Hopefully I won’t run into this again because I love their filament itself. Just can’t babysit the reel advancement.